Developed for applications where compact size and minimal above panel height is paramount, the JC025 and JC030 rockers are very low profile whilst still providing precise fingertip control in one axis. The use of these rockers in a control panel allows designers to develop very low profile assemblies whilst still maintaining the functionality of a much larger single axis joystick. These rockers have been designed for maintenance-free operation throughout an operating life of greater than five million operations. Typical applications include remote control chest packs, pendant controllers, low profile panel assemblies and control consoles.

For paddle style joysticks see JC100 and JC120

More Info

Developed for applications where ergonomics and system integrity are paramount, the JC100 is a compact, low profile joystick that provides smooth, precise fingertip control in one axis. The JC100 is sealed to IP66 to enable it to operate in extreme environments. With all the components contained within the handle, and standing only 70mm high, it is ideal for mounting in low profile panels and arm rests. Installation time has been reduced through the use of a standard electronic connector, and the joystick has been designed for maintenance-free operation throughout its operating life of greater than 5 million operations. Typical applications include remote control chest packs and the control of construction, agricultural or material handling equipment.

Also see JC120

For switched or detent single axis operation see JC3000

For hand controlled single axis joysticks see JC150 and JC6000

More Info

Developed for applications where ergonomics and system integrity are paramount, the JC120 is a minimum width, low profile joystick that provides smooth, precise fingertip control in one axis with a choice of two lever lengths. The JC120 is sealed to IP66 to enable it to operate in extreme environments. Standing only 54 or 64mm high, the JC120 is less susceptible to unintentional operation. With all of the components contained within the handle, it is ideal for mounting in low profile panels and arm rests. Installation time has been reduced through the use of a standard electronic connector, and the joystick has been designed for maintenance-free operation throughout on operating life of greater than 5 million operations. An optional neoprene boot is available for the short handle version, allowing operation in environments where aggressive materials are present, protecting from dust and dirt ingress. Typical applications include remote control chest packs and the control of construction, agricultural or material handling equipment.

Also see JC100

For switched or detent single axis operation see JC3000

For hand controlled single axis joysticks see JC150 and JC6000

More Info

 

The JC150 single-axis joystick controller is designed for demanding operatorcontrol applications in off-highway vehicles and other man-machine interfaces,where lever strength, signal reliability, and handle functionality are important. The JC150 joystick is supplied with a long life conductive plastic potentiometer track and directional/center off or end switches to provide signals for sensing lever direction and fault detection. The JC150’s compact size, high lever strength and superb proportional control are ideal for applications which include operator controls on a wide range of off-highway vehicles, including cranes, loaders, excavators, access platforms, tractors and harvesters. A switched JC150 without directional switches is available.

For fingertip single axis joysticks see JC100 and JC120

For switched or detent single axis operation see JC3000

For Hall Effect single axis joysticks see JC6000

More Info

A compact, inductive joystick with a life inexcess of 15 million operations and EMCimmunity of 50V/m, the JC200 offers fingertip control in two axes. Designed for use with an electronic controller, the inductive circuit inside the JC200 generates analogue signals proportional to the distance over which the handle is moved in either axis. This output is configured to provide signals for fault detection circuits within the controller,whilst a center tap provides an accurate voltage reference for the center position. The inductive circuit can be mounted at 45 degrees to the normal axis to provide reference signals for dual channel motor controllers. The output voltage range can be further restricted in one or more directions, by the selection of the correct gate geometry. This can be used to limit, for example, the maximum speed of a vehicle when reversing around a corner. Typical applications include the control of wheelchairs, fork lift trucks and agricultural machinery.

The JC200 is being replaced by the JC2000

For Hall Effect joysticks see JC2000 and JC6000

More Info

The JC2000 contactless joystick controller is designed for precision fingertip control applications where safety and long, trouble-free life are primary requirements. It is available in one, two or three axis configurations and can accommodate a choice of handles, including push-button switch versions. Two mounting flange options allow attachment above or below the panel. The JC2000’s compact size, low operational force and high reliability are ideal for applications which include powered wheelchairs, robotics, CMM machines, medical and CCTV equipment, professional camera controls and remote controlled chest-packs.

For other Hall Effect joysticks see JC6000

More Info

Developed for those applications whereweight and functionality are paramount, the JC300 offers switched or proportional fingertip control in up to three axes. Designed for use with an electronic controller, the JC300 can be specified to generate up to five switched outputs perhalf axis, or analogue and switched reference signals. This analogue output can be configured to provide signals for fault detection circuits within the controller. A center tap on the analogue track provides an accurate voltage reference for the center position or a zero point for a bipolar supply voltage. The JC300's range of ergonomic handles feature rotary operated potentiometers for a third axis of control or Deadman's switches that can be used to improve the integrity of your control system. Installation time has been reduced through the use of standard electronic connectors, whilst the absence of all micro switches and camshafts has eliminated the need to maintain the joystick throughout its operating life of in excess of four million cycles. Typical applications include remote controlchest-packs and the control of agricultural attachments.

The JC300 is being replaced by the JC3000

More Info

The JC3000 joystick controller is designed for applications requiring a simplistic approach to fingertip control, where strength, and reliability are important. The JC3000 is a dual axis controller that has mechanical detent features, in both axes, that provide feedback to the operator allowing the operator to determine the angular position of the joystick. The position of the detents relate to customer specific switch outputs. The operating rod of the joystick is designed to accommodate a customer specific handle. Typical applications include remote control chest packs and the control of construction, agricultural or material handling equipment.

The JC3000 replaces the JC300

More Info

Developed for use in applications where compact size and functionality are important, the JC400 with analogue output offers proportional fingertip control in up to three axes. The JC400's range of ergonomic handles feature rotary operated potentiometers, or switches, for a third axis of control, or 'Person Present' switches that can be used to improve the integrity of your control system. Installation flexibility has been provided by using different forms of mounting flanges independent of the function of the joystick and the analogue track models are supplied with side exit cables to minimize the required under panel depth. The joystick has been designed for maintenance-free operation throughout an operating life of greater than 5 million operations. Typical applications include remote control chest packs, CCTV camera controls and the operator controls in construction,agricultural or material handling equipment.

For Hall Effect fingertip joysticks see JC2000

For hand controlled joysticks see JC6000

More Info

The JC600 joystick has been replaced with the JC6000 joystick listed below. However information is still available for the device; please click below for more information.

More Info

The JC6000 rugged joystick controller is designed for demanding operator control applications in off-highway vehicles and other man-machine interfaces, where strength, reliability, and handle functionality are important. Available in one or two axis configurations, this joystick can be supplied with non-contact Hall effect sensors or long life potentiometer tracks. The JC6000’s compact size, high lever strength and superb proportional control are ideal for applications which include operator controls on a wide range of off-highway vehicles, including cranes, loaders, excavators, access platforms, tractors and harvesters.

The JC6000 is available with J1939 and CANOpen output.

More Info