Back to Digital Meters
 
 
 
  JUNIOR Series
     
 
JR-C / JR20-C
JR-C / JR20-C

DIGITAL METER for the following input signals:

LOAD CELL
 (±300mV, ±30mV)

JR-C and JR20-C models are specially designed for direct conection to load cells, they can be adapted to most existing cells in the market.
Easy to scale into desired engineering units, directly by frontal keys or real input signal value in teach mode.

Universal AC/DC voltage supply.

Fully configurables through 3 frontal keys, they allow signal input type selection and also provide a 5 or 10V DC and up to 30mA load current output for sensor excitation.

4 digit indicator with 14mm digit and –9999 to 9999 display range for JR-C
• 4 digit indicator with 20mm digit
 and –1999 to 9999 display range for JR20-C
• Configurable decimal point
 for JR-C and JR20-C

Detection, saving, later recalling and resetting of maximum and minimum values reached by the input signal since last reset activation. Reset function sets automatically memorized value to current input signal value when maximum or minimum value are displayed.
Maximum and minimum values recalling to display and reset functions are directly available through frontal keys.
TARE and TARE RESET functions available through frontal key or through a logic (O.C) or contact switch input present at rear connector for a remote activation.
     
     
   
 
JR-D / JR20-D
JR-D / JR20-D

DIGITAL METER for the following input signals:

HIGH VOLTAGE
 (10 to 600V AC)
SENSORS: MAGNETIC, NAMUR, NPN and PNP
TTL/24V ENCODER
CONTACT SWITCH

JR-D and JR20-D models, accept most commonly used pulse generators or transducers to work as an unidirectional counter, tachometer or frequency meter (rpm or rate).
They have configurable factor and offset when are programmed as a counter or easily scalables into desired engineering units working as tachometer or frequency meter.

Universal AC/DC voltage supply.

Fully configurables through 3 frontal keys, they allow signal input type selection and also provide 8V or 24V DC up to 60mA or 30mA load current output respectively for sensor excitation.

• 4 digit indicator with 14mm digit and –9999 to 9999 display range for JR-D
• 4 digit indicator with 20mm digit and –1999 to 9999 display range for JR20-D
• Configurable decimal point for JR-D and JR20-D 2RE option activates two alarms depending on display
programmed values, though not from totalizer which this is only an informative reading.

Configured as a counter has a totalizer (up to 999999) and a RESET function, available through frontal key or remotely. Besides current counting display, the totalizer brings the possibility of visualizing the cumulative number (divided in two parts) of pulses produced in multiple processes. Remote RESET is activated through contact switch input present at input rear connector. When configured as a frequency meter or tachometer it is also possible to adjust internal sampling time and time limit, thus providing specific application adaptation.

Detection, saving, later recalling and resetting of maximum and minimum values reached by display since last reset activation (functions not available for counter mode).
     
     
   
 
JR-E / JR20-E

JR-E / JR20-E

DIGITAL METER for the following input signals:

• DC VOLTAGE
 (±600V, ±200V and ±20V)
• DC CURRENT (±5A, ±1A, ±100mV and ±60mV)
• AC VOLTAGE (0-600V, 0-200V and 0-20V)
• AC CURRENT (0-5A, 0-1A, 0-100mV and 0-60mV)

JR-E and JR20-E models admit both alternating and direct voltage and current signal inputs for industrial signal monitoring. Easy to scale into desired engineering units, directly by frontal keys or real input signal value in teach mode.

Universal AC/DC voltage supply. Fully configurables through 3 frontal keys, they allow signal input type. 

• 4 digit indicator with 14mm digit and –9999 to 9999 display range for JR-E
• 4 digit indicator with 20mm digit and –1999 to 9999 display range for JR20-E
Configurable decimal point for JR-E and JR20-E

Detection, saving, later recalling and resetting of maximum and minimum values reached by the input signal since last reset activation.


Reset function sets automatically memorized value to current input signal value when maximum or minimum value are displayed. Maximum and minimum values recalling to display and reset functions are directly available through frontal keys.
Capable of measuring AC/DC voltage in 600V, 200V and 20V ranges, AC/DC current directly or through a current transformer in 5A and 1A ranges or through an external shunt in 60mV and 100mV ranges. 
     
     
   
 
JR-P / JR20-P
JR-P / JR20-P

DIGITAL METER for the following input signals:

• PROCESS (±10V, ±200V and ±20mA) 
• TEMPERATURE (Pt100, Pt1000, TC J, K, T and N) 
• POTENTIOMETER (100 Ohm to 100 KOhm)
• RESISTANCE (999.9 Ohm 9999 Ohm and 50.00 KOhm) 

JR-P and JR20-P models admit several signal input types to control industrial processes. Easy to scale into desired engineering units, directly by frontal keys or real input signal value in teach mode.

12V to 230V Universal AC/DC voltage supply

Fully configurables, they allow signal input type selection and also provide a 24V DC @ 30mA output for sensor excitation.

• 4 digit indicator with 14mm digit and –9999 to 9999 display range for JR-P
• 4 digit indicator with 20mm digit and –1999 to 9999 display range for JR20-P
• Configurable decimal point for JR-P and JR20-P


Detection, saving, later recalling and resetting of maximum and minimum values reached by the input signal since last reset activation. Reset function sets automatically memorized value to current input signal value when maximum or minimum value are displayed. Maximum and minimum values recalling to display and reset functions are directly available through frontal keys.
Capable of measuring 3-wire Pt100 and 2-wire Pt1000 (IEC 60751) and Thermocouple (IEC 60584-1), 3-wire Potentiometer, 2-wire Resistance and Process input signals.
     
     
   
 
     
Back to Digital Meters